R1 vs R2 Hydraulic Hose: SAE 100R1AT vs 100R2AT
Updated · 7 min read
Choosing between R1 and R2 hydraulic hose? Compare construction, working pressure and the purchase checks that matter before approving a replacement.

What Are SAE 100R1AT and 100R2AT?
R1 and R2 are common purchase descriptions for steel-wire-braided hydraulic hose. SAE 100R1AT uses one braid; SAE 100R2AT uses two. The full designations matter: ask for the manufacturer, series and complete marking, rather than placing an order for “rubber hydraulic pipe” alone.
These types sit within SAE J517, the hydraulic-hose standard. A type designation describes requirements for a hose family. It does not identify the machine circuit, end fittings or complete replacement assembly. Two quotations carrying “R2” still need a product-by-product comparison.
For maintenance buyers, the useful question is: does the offered hose-and-fitting combination meet the documented requirement for this line? Start with the equipment specification and the existing assembly reference. Use the comparison below to understand the difference, then obtain the exact data sheet before approving a purchase.
Construction: One Steel-Wire Braid vs Two
Both types have an inner tube, reinforcing wire and an outer cover. In the Gates G1/G2 examples cited here, the tube is nitrile-based and the cover is nitrile/PVC-based. G1 has one high-tensile steel-wire braid and G2 has two. These material descriptions belong to those catalogue products; other series need their own data.
The extra braid does not mean every R2 product has exactly twice an R1 product’s working pressure. It also does not prove identical flexibility or outside diameter. Keep the size row and product identity together when checking a proposed replacement.
A storekeeper can help by photographing the printed hose marking before it becomes unreadable. Include the complete line of text and both ends in the enquiry. A photograph of the black cover alone gives the purchase team very little evidence for choosing between two similar-looking offers.
R1 vs R2 Working Pressure: Five Common Sizes
Source for every row: Gates Hydraulic Hose & Couplings Catalogue No. 50080, Edition 2024, G2 p. 58 and G1 p. 59. Pressures are the published MPa values converted to bar (1 MPa = 10 bar). Millimetres are exact conversions of the nominal inch bore (1 inch = 25.4 mm), not measured IDs or the catalogue’s rounded DN labels.
| Dash Size | Nominal ID (Inch) | Nominal ID (mm Equivalent) | R1AT: G1 Max WP (bar) | R2AT: G2 Max WP (bar) |
|---|---|---|---|---|
| -4 | 1/4 | 6.35 | 225 | 400 |
| -6 | 3/8 | 9.525 | 180 | 330 |
| -8 | 1/2 | 12.7 | 160 | 275 |
| -12 | 3/4 | 19.05 | 105 | 215 |
| -16 | 1 | 25.4 | 90 | 165 |
Read this as a named-product comparison, not a universal SAE pressure table. Gates lists these series against SAE 100R1AT/100R2AT and EN 853 1SN/2SN. Other catalogue editions or products may differ. No RHPL hose or finished-assembly rating is declared here.
Read across the same row before reading down a column. A number copied from a different bore is not a valid basis for selection. Ask the supplier to attach the offered product’s current sheet to the quotation so the purchase order can refer to an identifiable document.
Typical Applications and Their Limits
Single-braid R1AT hose is commonly considered for moderate-pressure hydraulic duties; two-braid R2AT is considered where the specified duty needs the higher pressure capability of that product and size. Hydraulic power packs, agricultural equipment, workshop machinery and mobile equipment can contain lines in these categories. That is application context, not a recommendation for every line on those machines.
For example, an enquiry describing a “loader hydraulic hose” is incomplete. Add the circuit or assembly reference and the equipment requirement. Likewise, a plant shutdown list should distinguish each accepted assembly rather than grouping every hose under one generic R2 description.
Do not assume either type suits suction, steam, oxygen, a different chemical or a special mining requirement. Such duties need explicit product suitability. BSI’s EN 853 scope also points out that underground-mining hose requirements are addressed in other documents.
How to Choose for a Replacement
Use the following checks with the responsible maintenance engineer. Parker’s Safety Guide, Publication 4400-B.1 (November 2007), supports checking service conditions and compatible components; consult current product instructions for the actual order.
- Confirm the duty: identify the equipment, circuit, fluid and required bore. Record operating pressure including surges, fluid temperature and surrounding heat.
- Compare exact products: check the selected size’s working pressure, fluid compatibility and temperature limits. A steady gauge reading may miss pressure peaks.
- Check the route: compare outside diameter, bend requirements, movement and clamp clearance. Do not force a replacement into a route it cannot accommodate.
- Confirm assembly compatibility: verify hose, stem, ferrule and assembly instructions as a combination. Matching the machine-end thread alone is insufficient.
- Document approval: put the accepted series, assembly reference and any approved alternative on the purchase record. Resolve missing information before release.
A useful quotation comparison has a separate column for exceptions. If one supplier changes the brand, end style or proposed hose family, ask for that difference to be written explicitly. This prevents an apparently simple repeat order from becoming an undocumented substitution.
1SN vs 2SN (EN 853)
EN 853 uses 1SN for a single-wire-braid type and 2SN for a two-wire-braid type. They are related to the R1AT/R2AT comparison, and named products may carry both SAE and EN declarations. However, similar construction does not make the standards blanket-equivalent or every product interchangeable.
Check the exact manufacturer declaration, size and required standard edition. The Gates 2024 catalogue supplies the examples on this page; it is not evidence of compliance with a later edition. The separate BSI reference below is BS EN 853:2026 and is cited for its published scope, not as the source of the pressure table.
For a tender specifying 2SN, do not silently replace that wording with R2 on the offer. State the offered series and attach its declared compliance. If the tender requires both standards, obtain evidence for both. The buyer should be able to follow the requirement from enquiry through quotation to the supplied product identification.
Hose Rating and Assembly Rating Are Different
SAE J517 (July 2020) states that an assembly’s maximum working pressure must not exceed the lower applicable rating of its hose and connectors. The hose-only table therefore cannot establish the finished assembly’s allowable pressure. The selected combination and its assembly instructions still matter.
Do not treat burst pressure as an operating allowance. A catalogue pressure comparison also cannot certify a repaired hose or validate an unapproved coupling. For a replacement purchase, request the complete assembly specification and record who accepted it for the intended service.
What to Include in Your Enquiry
Send the machine and assembly reference, readable marking photographs, both end views, required quantity and destination. Include the approved drawing or dimensional information privately, plus known service conditions. If a detail is unknown, mark it as unknown so the technical review can resolve it.
Ask for confirmation of the exact hose series, end identification and any proposed deviation. Browse our hydraulic hoses and hose assemblies, use the hydraulic fittings names chart for identification, or send an RFQ with your requirement.
Frequently Asked Questions
What Is the Main Difference Between R1 and R2 Hose?
R1AT has one steel-wire braid; R2AT has two. Compare the exact series and bore because the type name alone does not establish the pressure rating for your replacement.
Is R2 Always Better Than R1?
No. The correct choice meets the documented circuit and assembly requirements. A higher catalogue pressure does not by itself confirm fitment or justify changing an approved specification.
Can I Replace R1 With R2?
Only after the responsible technical team accepts the specific replacement. Ask the supplier to identify the proposed product and all differences from the existing approved assembly.
Are 1SN and R1AT, or 2SN and R2AT, the Same?
They are related designations under different standards. Accept dual compliance only where the manufacturer declares it for the offered product; do not assume universal equivalence.
Why Do R1 or R2 Pressure Tables Differ Online?
Check the product, bore, units and edition. Some tables give standard requirements, others manufacturer product values. This table identifies its catalogue and conversions so the figures are traceable.
Does the Hose Pressure Apply to the Complete Assembly?
Not automatically. The applicable connector rating can limit the assembly. Obtain the accepted hose-and-coupling specification instead of copying a hose-only number onto the purchase order.
Technical References
Consult the current product and equipment instructions for the proposed application. The references below support the general technical background; they do not validate an RHPL assembly.
- Gates Hydraulic Hose & Couplings Catalogue No. 50080, Edition 2024 — G2 p. 58; G1 p. 59
- SAE J517_202007 — Hydraulic Hose, July 2020; Public Scope and Assembly Pressure Rule
- BSI: BS EN 853:2026 — Published Scope, 30 April 2026
- Parker Safety Guide 4400-B.1, November 2007 — Catalog 4400 US, Technical Section
Caterpillar, Volvo, Komatsu, Hitachi, Danfoss, Parker, Manuli and Swagelok are trademarks of their respective owners. RHPL is not affiliated with or endorsed by these brand owners. Gates is a trademark of Gates Corporation; RHPL is an Authorised Gates Distributor. Brand and machine names are used only to identify compatibility. External manufacturer references provide general technical background and do not imply endorsement of RHPL products.
